Hjælp til Roger™ Touchscreen Mic

Ofte stillede spørgsmål

 
Beautyshot Roger Touchscreen Mic
 

Roger Touchscreen Mic

Q: How many Roger devices can be connected in the same network by the primary Roger microphone?

A:

  • Unlimited number of Roger receivers
  • Up to 35 Roger microphones
  • Maximum 1 Roger Multimedia Hub when mixing network mode is selected
  • Maximum 1 Roger DigiMaster 5000
  • Up to 2 Roger DigiMaster 7000
  • Up to 5 Roger DigiMaster X

Q: Is it possible to integrate Roger Touchscreen Mic to an existing classroom network, where the primary is a Roger inspiro?

A:

  • Yes, press connect from the Roger inspiro within 10cm / 4” of the Roger Touchscreen Mic
  • Roger inspiro must be in Roger only mode

Q: Is it possible to integrate Roger inspiro into a classroom network, where the primary is a Roger Touchscreen Mic?

A:

  • Yes, in the network mode of the Roger Touchscreen Mic, select Primary Talker mode or Equal Talker mode.
  • Then press Connect on the Roger Touchscreen Mic within 10cm / 4” of Roger inspiro.
  • Remark: the specific Roger Touchscreen Mic feature – Mixing - will not be available in that configuration

Q: How do I know if the Roger Touchscreen Mic is the primary in the classroom network?

A: On the upper left part of the display a “1” is displayed

Q: How do I connect a Roger receiver to a Roger microphone?

A:

  • Make sure your Roger Touchscreen Mic  and Roger receiver are both switched on.
  • Hold your Roger Touchscreen Mic  within 10 cm / 4” of the Roger receiver.
  • Tap  Connect on your Roger Touchscreen Mic.
  • Simply repeat these steps to connect additional Roger receivers.

Q: Is Roger Touchscreen Mic compatible with Phonak Dynamic SoundField classroom amplification systems?

A: Yes, Roger Touchscreen Mic can be used out of the box with Phonak Roger Dynamic SoundField system after tapping  Connect function.

Q: Is Roger Touchscreen Mic compatible with other manufacturer’s soundfield systems?

A: Yes, Roger Touchscreen Mic can be used with other soundfield systems. A piece of hardware is required - Roger DigiMaster X. Roger DigiMaster X  needs to be wired connected to other soundfield systems. Afterwards,  tap Connect Roger Touchscreen Mic to connect Roger DigiMaster X.  

Q: Can I connect a Roger Pen or Roger Clip-On Mic to a network with a Roger Touchscreen Mic?

A: No. The Roger Touchscreen Mic can be in a network with other Roger Touchscreen Mics, Roger Pass-arounds, Roger Multimedia Hubs, Roger inspiros, Roger DynaMics, and Roger AudioHubs.

Q: Can I program a name to Roger receiver?

A: Yes, use either directly  the Settings menu in Roger Touchscreen Mic and select Name  under Roger receiver settings. Alternatively use the Roger Upgrader software available for free download

Q: How can I go back to home screen in Roger Touchscreen Mic?

A: Short press on  On/Off button.

Q: Can I connect another microphone when Roger Touchscreen Mic is in Small Group Mode?

A: No, it is not possible to connect additional microphones to the network when in Samll Group Mode. It is however possible to attach additional receivers.

Q: Can I add a microphone - Roger Touchscreen Mic or Roger Pass-around or a hub to a network by using a Roger WallPilot?

A: Yes. Turn the device off and on again in front of the Roger WallPilot.

Q: Can I use JoinNet on Roger Touchscreen Mic when using a Roger WallPilot to join a network?

A: Yes. Tap JoinNet in front of Roger WallPilot.

Q: Why is Pointing greyed out in the Microphone mode menu in my Roger Touchscreen Mic?

A: If Pointing Mode is required, it can be activated or deactivated under Settings menu.

Q: Can I see which devices are connected in the same network?

A: Yes. Tap List devices on Roger Touchscreen Mic. Connect icon is displayed on the right side when the device is in the same network and device name is bold.

Q: EasyGain sliding scale. What is the number for each sliding step?

A: Each +/– step represents a change in gain of 2 dB up to max. 8 dB higher/lower than middle setting. Middle setting is the delivered factory setting.

Q: Can EasyGain function be used with several Roger receivers at the same time?

A: No, each Roger receiver has to be adjusted individually by selecting “Roger receiver settings” in the Roger Touchscreen Mic settings menu then selecting “EasyGain level” and adjusting the level. For the next Roger receiver, select again “Roger receiver settings” then select “EasyGain level “ to adjust the level and so on…

Q: Can I change the activation time of screen saver?

A: Yes. Tap Settings icon, select  Display, select Screen saver and choose appropriate activation time.

Q: Is it correct that Roger DigiMasters and secondary Roger microphones are not active in the Network when Small Group mode or Pointing mode is activated in Primary Roger Touchscreen Mic?

A: Yes.  All Roger DigiMasters and secondary microphones in the MultiTalker Network are automatically and temporarily disabled. When Primary Roger Touchscreen Mic returns to the lanyard, the Network is automatically restored. Roger DigiMasters and secondary Roger microphones  are enabled again.

Q: Is it correct that Roger DigiMasters and secondary Roger microphones cannot be connected to Roger Touchscreen Mic, when Small Group mode or Pointing mode is in used?

A: Yes.  When Small Group mode or Pointing mode is active in Roger Touchscreen Mic, only Roger receivers can be connected to the Roger Touchscreen Mic.  

Q: Which CI profile for Roger X is suitable for CI (Cochlear Implant)?

A: CI Profiles

·         Automatic

·         Profile 1 – not applicable

·         Profile 2 Opus 2

·         Profile 3 Naída CI+ComPilot/ Sonnet

·         Profile 4 Neptune/ Harmony/ Auria +8dB EasyGain

·         Profile 5 MicroLink CI S

·         Profile 6 – not applicable

·         Profile 7 – not applicable

·         Profile 8 – not applicable

·         Profile 9 Nucleus 5, 6

Q: How to select a CI profile for Roger X?

A: Tap Settings icon, ensure Roger receiver is located within 10 cm / 4” of Roger Touchscreen Mic, select Roger receiver settings menu, select CI profile menu , select appropriate profile e.g. automatic.

Q: Can I update Roger Touchscreen Mic?

A: Yes, use the Roger Upgrader software, which is available for free download in the web Phonakpro.com

Q: What if “Frowning face” is displayed on Roger Touchscreen Mic and after 30 seconds the device did not reboot automatically?

A: Reset manually the device  by pressing  and holding On/Off and Mute buttons simultaneously for at least eight seconds.

Q: Can Mass Connect connect only receivers?

A: Correct. Mass Connect can only be used to connect Roger receivers but no Roger microphones or Roger Soundfield.

Q: Can Mass Connect connect only receivers?

A: Correct. Mass Connect can only be used to connect Roger receivers but no Roger microphones or Roger Soundfield.

Q: Is microphone mode locked when activating Quick Menu?

A: Yes. if Roger Touchscreen Mic is running firmware version  1.2 or higher. The microphone mode ( lanyard or automatic or small group or pointing) selected before activating Quick Menu will be locked. It will be remained locked until the Quick Menu is disabled.

Q: Can I use Roger Touchscreen Mic to upgrade the firmware of a Roger receiver?

A: Yes. To upgrade the firmware of a Roger receiver, Roger Upgrader software and a device shall be used as a relay between the PC and the Roger receiver. The device can be either Roger Touchscreen Mic or Roger inspiro. The device shall be properly connected to the USB port of the PC. The Roger receiver shall be attached to its hearing instrument or CI processor and placed close to the device.

Q: Why to use the automatic Primary handover feature in Roger Touchscreen Mic?

A: For modern teaching, a Roger Network supports MTN – MultiTalker Network. A MTN allows up to 35 Roger microphones such as Roger Touchscreen Mic or Roger Pass‐around to be used in the same MTN Roger network. A MTN Roger Network can be created by any Roger Touchscreen Mic, which will become the Primary for the MTN. However, for some reasons the Primary might leave the room. The replacement of the Primary leaving the room by another Roger Touchscreen Mic available in the network will be done seamlessly and automatically.

Q: What is the automatic Primary handover feature in Roger Touchscreen Mic?

A: The automatic Primary handover feature allows to keep automatically the Roger network intact when the Roger Touchscreen Mic, which is the Primary of the Roger Network is leaving.

Q: How to use the automatic Primary handover feature in Roger Touchscreen Mic?

A: Simply, use any Roger Touchscreen Mic running firmware v2.0 or higher to create a MTN Roger Network and to be a Primary. All Roger Touchscreen Mic in the MTN Roger network shall run firmware v2.0 or higher to support the automatic Primary handover.

    

Roger Pass-around

Q: Does Roger Pass-around need to be restarted when using a Roger Touchscreen Mic to change settings?

A: No, changes are immediately applied.

Q: Do I need to turn on all Roger Pass-arounds to activate Push-To-Talk function in Roger Touchscreen Mode?

A: No. Each Roger Pass-around applies changes when it is turned on.

Q: If the volume of the Roger Pass-around has been changed via the volume button, does it reset to default settings after turning off?

A: Yes, no changes are stored after turning off the device.

Q: How do I know if Push-To-Talk function has been activated within the Roger Pass-around?

A: The indicator lights are orange for the microphones in stand-by and green for the active microphone.

Q: Can I use the Roger Pass-around with Roger inspiro as Primary microphone in the network?

A: Yes, Roger Pass-around  is compatible to Roger inspiro microphone. However some features will not be available: No FM available, No PTT (push-to-talk) mode available. factory settings for Roger Pass-around will be applied:  Auto-mute activated. Mute button deactivated. Volume button activated.

Q: Which Roger Pass-around firmware version is compatible to Roger inspiro SoundField only?

A: Roger Pass-around running firmware version v1.2 is compatible to Roger inspiro SoundField only. For some temporarily reasons Roger Pass-around running firmware version v1.3 is not compatible to Roger inspiro SoundField only. It is recommended to download Roger Pass-around firmware from v1.3 to v1.2 when Roger Pass-around is in use with Roger inspiro SoundField only.

    

Roger Multimedia Hub

Q: Can Roger Multimedia Hub connect to a DigiMaster, when it is usd as a stand-alone media transmitter?

A: No, only Roger receivers can be connected to Roger Multimedia Hub.

Q: How to apply NewNet on Roger Multimedia Hub?

A: Press simultaneously On/Off and Connect button during 8 seconds.

Q: Can Roger Multimedia Hub connect Roger microphone?

A: No, Roger Multimedia Hub can connect only Roger receivers.

Q: how can I know if Roger Multimedia Hub is broadcasting the audio?

A: First,  press on Connect button within 10cm / 4” of the Roger receivers attached to the Hearing Aids.  Connect with the cable the audio source to the Roger Multimedia Hub. Let start playing the audio then the green indicator light around the Connect button will blink.

Q: Can multiple Roger Multimedia Hub be used with different children in one room (individual use)?

A: Yes, multiple Roger Multimedia Hubs in their own network can be used in one room.

Q: Can I add a Roger Multimedia Hub to a network by using a Roger WallPilot?

A: Yes. Turn the device off and on again in front of the Roger WallPilot or press JoinNet Menu in Roger WallPilot near Roger Multimedia Hub.

Q: Can Roger WallPilot be used to manage Roger receivers coming into a classroom with Roger Multimedia Hub used in stand-alone only?

A: No. For Roger Multimedia Hub in stand-alone usage each receiver needs to be connected via the connect button on the Roger Multimedia Hub.

Q. Which Roger Multimedia Hub firmware version is compatible to Roger inspiro SoundField only?

A: Roger Multimedia Hub running firmware version v1.2 is compatible to Roger inspiro SoundField only. For some temporarily reasons Roger Multimedia Hub  running firmware version v1.3 is not compatible to Roger inspiro SoundField only. It is recommended to download Roger Multimedia Hub firmware from v1.3 to v1.2 when Roger Multimedia Hub is in use with Roger inspiro SoundField only.

Q: Can several Roger Multimedia Hub be connected in the same Roger Network?

A: No. Only one.

    

Roger Repeater

What is the Roger Repeater?

The Roger Repeater is a Roger range extender device, which will extend the operating range of any Roger network in the schools. 

How many Roger Repeater can be used in the same Roger network?

Usually up to four Roger Repeaters will be used to cover a large room/gym in the schools. But if needed,  additional Roger Repeaters can be added. 

Can Roger Repeater be used together with Roger DigiMaster loudspeakers in the same Roger network?

Yes. 

Can Roger Repeater be connected to Roger Touchscreen Mic?

Yes.

Can Roger Repeater be connected to Roger inspiro?

Yes.

Can Roger Repeater be connected to Roger Pen?

No.

How to connect Roger Repeater?

The primary Roger microphone in the network is used to connect all Roger Repeater ( one or more) in the same Roger network. 

Where should I place Roger Repeater in a room?

The Roger Repeater is optimized to operate when mounted on the wall in room, gym hall, or auditorium (at 1.5 - 2 m/ 5 - 7 ft height with the wall mount that is delivered in packaging). The Roger Repeater needs to be placed in the operating range of the primary Roger microphone in the network or in the range of another Roger Repeater already connected to the primary microphone.

Which Roger devices are compatible to Roger Repeater?

The Roger Repeater is compatible to all Roger Educational microphones, Roger (02) receivers, Roger DigiMaster SoundField.

How do I power Roger Repeater?

Roger Repeater can be plugged into the mains or can run off the rechargeable battery inside. The device can be charged individually or by using the Roger Charging Rack, which can accommodate up to 4 devices.

Can a Roger Repeater be connected simultaneously to several different Roger networks in a room?

No. Each Roger Repeater is only connected to one Roger network at a time. If several different Roger networks are simultaneously in use in the same room, each single Roger network needs to connect  one (or more)  Roger Repeaters in its network to extend the range of both networks.

    

    

Spørgsmål: Hvor mange Roger-enheder kan forbindes i samme netværk med den primære Roger-mikrofon?

Svar:

  • Ubegrænset antal Roger-modtagere
  • Op til 35 Roger-mikrofoner
  • Maksimalt én Roger Multimedia Hub, når netværksindstillingen for mixing er valgt
  • Maksimalt én Roger DigiMaster 5000
  • Op til to Roger DigiMaster 7000
  • Op til fem Roger DigiMaster X

Spørgsmål: Er det muligt at integrere Roger Touchscreen Mic i et eksisterende klasseværelses netværk, hvor den primære enhed er en Roger inspiro?

Svar:

  • Ja, tryk på Tilslut fra Roger inspiro inden for 10cm fra Roger Touchscreen Mic’en
  • Roger inspiro skal være i indstillingen Kun Roger

Spørgsmål: Er det muligt at integrere Roger inspiro i et eksisterende klasseværelses netværk, hvor den primære enhed er en Roger Touchscreen Mic?

Svar:

  • Ja, i netværksindstillingen for Roger Touchscreen Mic skal du vælge indstillingen Primær taler eller Ligeværdige talere
  • Derefter skal du trykke på Tilslut på Roger Touchscreen Mic’en inden for 10 cm fra Roger inspiro
  • Bemærkning: Den specifikke Roger Touchscreen Mic funktion (dvs. Mixing er ikke tilgængelige i denne konfiguration

Spørgsmål: Hvordan kan jeg vide, om Roger Touchscreen Mic er den primære enhed i klasseværelsets netværk?

Svar: "1" vises i den øverste venstre del af skærmen

Spørgsmål: Hvordan tilslutter jeg en Roger-modtager til en Roger-mikrofon?

Svar:

  • Sørg for, at din Roger Touchscreen Mic og din Roger-modtager begge er tændt.
  • Hold Roger Touchscreen Mic inden for 10 cm fra Roger-modtageren.
  • Tryk på Tilslut på Roger Touchscreen Mic.
  • Gentag disse trin for at tilslutte yderligere Roger-modtagere.

Spørgsmål: Er Roger Touchscreen Mic kompatibel med lydforstærkningssystemet til klasselokaler Phonak Dynamic SoundField?

Svar: Ja, Roger Touchscreen Mic kan med det samme bruges sammen med Phonak Roger Dynamic SoundField, når du trykker på Tilslut.

Spørgsmål: Er Roger Touchscreen Mic kompatibel med producentens øvrige SoundField-systemer?

Svar: Ja, Roger Touchscreen Mic kan bruges sammen med andre SoundField-systemer. Der kræves et ekstra stykke hardware – Roger DigiMaster X. Roger DigiMaster X skal tilsluttes med kabel til de øvrige SoundField-systemer. Efterfølgende trykkes på Tilslut for at slutte Roger Touchscreen Mic til Roger DigiMaster X.

 

Spørgsmål: Er det muligt at forbinde en Roger Pen eller Roger Clip-On Mic til et netværk med en Roger Touchscreen Mic?

Svar: Nej. Roger Touchscreen Mic kan anvendes i et netværk med andre Roger Touchscreen Mics, Roger Pass-around-mikrofoner, Roger Multimedia Hubs, Roger inspiros, Roger DynaMics og Roger AudioHubs.

Spørgsmål: Kan jeg programmere et navn til Roger-modtageren?

Svar: Ja, du kan enten gå direkte via menuen Indstillinger i Roger Touchscreen Mic og vælge Navn under indstillinger for Roger-modtager. Ellers kan du bruge Roger-opgraderingssoftwaren, der kan downloades gratis.

Spørgsmål: Hvordan kommer jeg tilbage til startskærmen i Roger Touchscreen Mic?

Svar: Kortvarigt tryk på tænd/sluk-knappen.

Spørgsmål: Kan jeg tilslutte en ekstra mikrofon, når Roger Touchscreen Mic er i Small Group Mode?

Svar: Nej, det er ikke muligt at slutte ekstra mikrofoner til netværket i Small Group Mode. Men det er muligt at tilslutte ekstra modtagere.

Spørgsmål: Kan jeg tilslutte en mikrofon - Roger Touchscreen Mic eller Roger Pass-around eller en hub til et netværk ved hjælp af Roger WallPilot?

Svar: Ja. Sluk og tænd for enheden på forsiden af Roger WallPilot.

Spørgsmål: Kan jeg bruge JoinNet på Roger Touchscreen Mic, når jeg kobler på netværket via Roger WallPilot?

Svar: Ja. Tryk på JBin på forsiden af Roger WallPilot.

Spørgsmål: Hvorfor er Retningstilstand udtonet i menuen mikrofonitilstand i Roger Touchscreen Mic?

Svar: Hvis Interviewtilstand er påkrævet, kan den aktiveres eller deaktiveres under menuen Indstillinger.

Spørgsmål: Kan jeg se, hvilke andre enheder der er sluttet til netværket?

Svar: Ja. Tryk på Liste over enheder i Roger Touchscreen Mic. Ikonet Tilslut vises i højre side, når enheden er tilsluttet samme netværk, og enhedsnavnet er fedmarkeret.

Spørgsmål: EasyGain-skala. Hvad er værdien for hvert skalatrin?

Svar: Hver + /- trin svarer til en ændring i forstærkning på 2 dB op til maks. 8 dB højere/lavere end mellemste indstilling. Fabriksindstillingen er den mellemste indstilling.

Spørgsmål: Kan EasyGain-funktionen anvendes med flere Roger-modtagere samtidigt?

Svar: Nej, hver Roger-modtager skal justeres individuelt ved at vælge "Indstillinger for Roger-modtager" i indstillingsmenuen for Roger Touchscreen Mic og der vælge "EasyGain-niveau" og justere niveauet. Ved den næste Roger-modtager vælger du "Indstillinger for Roger-modtager" igen, "EasyGain-niveau" for at justere niveauet og så videre...

Spørgsmål: Kan jeg ændre pauseskærmens aktiveringstid?

Svar: Ja.Tryk på ikonet Indstillinger, vælg

Display, vælg Pauseskærm, og vælg en passende aktiveringstid.

Spørgsmål: Er det rigtigt, at Roger DigiMasters og sekundære Roger-mikrofoner ikke er aktive på netværket, når Gruppetilstand eller Interviewtilstand er aktiveret i Primary Roger Touchscreen Mic?

Svar: Ja.

Alle Roger DigiMasters og sekundære mikrofoner på MultiTalker Network deaktiveres automatisk midlertidigt.Når den primære Roger Touchscreen Mic vender tilbage til forelæsertilstand, genoprettes netværket automatisk.Alle Roger DigiMasters og sekundære Roger-mikrofoner aktiveres igen.

Spørgsmål:Er det rigtigt, at Roger DigiMasters og sekundære Roger-mikrofoner ikke kan tilsluttes Roger Touchscreen Mic, når Gruppetilstand eller Interviewtilstand anvendes?

Svar:Ja.

Når Gruppetilstand eller Interviewtilstand er aktiv i Roger Touchscreen Mic, er det kun muligt at slutte Roger-modtagere til Roger Touchscreen Mic.

Spørgsmål: Hvilken CI-profil til Roger X er egnet til CI (cochlea implants)?

Svar: CI-profiler

· Automatisk

· Profil 1 – anvendes ikke

· Profil 2 – Opus 2

· Profil 3 – Naída CI + ComPilot/Sonnet

· Profil 4 Neptune/Harmony/Auria + 8 dB EasyGain

· Profil 5 – MicroLink CI S

· Profil 6 – anvendes ikke

· Profil 7 – anvendes ikke

· Profil 8 – anvendes ikke

· Profil 9 – Nucleus 5, 6

Spørgsmål: Hvordan vælges en CI-profil til Roger X?

Svar: Tryk på ikonet Indstillinger, sørg for, at Roger-modtageren er placeret inden for 10 cm afstand af Roger Touchscreen Mic, vælg indstillingsmenuen for Roger-modtageren, vælg CI-profilmenuen, og vælg en passende profil, f.eks. automatisk.

Spørgsmål: Kan jeg opdatere Roger Touchscreen Mic?

Svar:Ja, brug Roger-opgraderingssoftware, som kan downloades gratis på websiden Phonakpro.com

Spørgsmål: Hvad hvis der vises et "Surt ansigt" på Roger Touchscreen Mic, og enheden ikke genstarter automatisk efter 30 sekunder?

Svar: Nulstil enheden manuelt ved at trykke på og holde knapperne On/Off og Mute nede samtidigt i mindst otte sekunder.

Spørgsmål: Kan Gruppetilslut kun tilslutte modtagere?

Svar: Korrekt.Gruppetilslut kan kun bruges til at tilslutte Roger-modtagere, men ikke Roger-mikrofoner eller Roger Soundfield.

Spørgsmål: Kan Gruppetilslut kun tilslutte modtagere?

Svar:Korrekt.Gruppetilslut kan kun bruges til at tilslutte Roger-modtagere, men ikke Roger-mikrofoner eller Roger Soundfield.

Spørgsmål: Kan Roger Pass-around blive i bordstanden, når jeg giver den videre til den næste person?

Svar: Ja, det er muligt at opbevare Roger Pass-around i letvægtsholderen.

Ofte stillede spørgsmål om Roger Pass-around

Spørgsmål: Skal Roger Pass-around genstartes for at overtage ændrede indstillinger, når jeg anvender en Roger Touchscreen Mic?

Svar: Nej, ændringerne overtages med det samme.

Spørgsmål: Skal jeg tænde for alle Roger Pass-around-mikrofoner for at aktivere Tryk-og-tal-funktionen i Roger Touchscreen-tilstanden?

Svar: Nej. Hver Roger Pass-around overtager ændringerne, når den tændes.

Spørgsmål: Hvis lydstyrken på Roger Pass-around er blevet ændret via lydstyrkeknappen, nulstiller den så til fabriksindstillingen, når den slukkes?

Svar: Ja, ændringerne bliver ikke gemt, når du slukker for enheden.

Spørgsmål: Hvordan ser jeg, om Tryk-og-tal-funktionen er aktiveret i Roger Pass-around?

Svar:Lysindikatorerne er orange for mikrofoner på standby og grøn for den aktive mikrofon.

Spørgsmål: Hvordan ser jeg, om Tryk-og-tal-funktionen er aktiveret i Roger Pass-around?

Svar: Lysindikatorerne er orange for mikrofoner på standby og grøn for den aktive mikrofon.

Ofte stillede spørgsmål om Roger Multimedia Hub

Spørgsmål: Kan Roger Multimedia Hub sluttes til en DigiMaster, når den anvendes som standalone media sender?

Svar: Nej, det er kun Roger-modtagere, der kan tilsluttes til Roger Multimedia Hub.

Spørgsmål: Hvordan aktiveres NewNet på Roger Multimedia Hub?

Svar: Tryk på tænd/sluk og Tilslut-knappen samtidig i otte sekunder.

Spørgsmål: Kan Roger Multimedia Hub tilslutte en Roger-mikrofon?

Svar: Nej, Roger Multimedia Hub kan kun tilslutte Roger-modtagere.

Spørgsmål: Hvordan ved jeg, om Roger Multimedia Hub sender lyden?

Svar: Først skal du trykke på knappen Connect inden for 10 cm afstand af de Roger-modtagere, der er sluttet til høreapparaterne. Slut lydkilden til Roger Multimedia Hub ved hjælp af kablet.Når afspilningen af lyden starter, blinker det grønne indikatorlys rundt om knappen Connect.

Spørgsmål: Er det muligt for forskellige børn i samme rum at anvende flere Roger Multimedia Hubs (individuel brug)?

Svar: Ja, der kan bruges flere Roger Multimedia Hubs på deres eget netværk i samme rum.

Spørgsmål: Kan jeg føje et Roger Multimedia Hub til et netværk ved hjælp af en Roger WallPilot?

Svar: Ja.Sluk og tænd for enheden på forsiden af Roger WallPilot.